USED FENDER JAPAN / TELECASTER ORDER [03]

FENDER JAPAN TELECASTER ORDER is in stock used.

Rear PU has been replaced with Duncan STR-3.
Front PU is model number unknown, but resistance value is around 7.8 ohm.
The pickguard may have been replaced as well. The front PU has open screw holes.
Both the neck and body pockets are stamped K-204. The neck pocket is stamped "A" and "ORDER".
The frets have been adjusted to match, so it is in good playing condition and can be used without any problems.

The overall condition of the guitar has some scratches and dents, but the strings have been replaced with new ones and the instrument has been cleaned, maintained, and set up by our repair department after it arrived at our store.
We also offer a 1-year warranty to ensure that you can use the instrument for a long time after purchase.

Serial number|A046147
Year of manufacture
Country of Manufacture|Japan
Case|Hard Case
Accessories|-
Weight|3.36kg
Truss Rod: No problem.
Fretboard: No problem, enough fretboard height
String height (bass string side)|2.0mm above 12th fret
String height(treble string side)|1.5mm above 12th fret
Nut width|42.75mm
Neck thickness(near 1st fret)|21.48mm
Neck thickness (near 12th fret)|24.52mm
SCALE|648mm (25.5")
RADIUS|184mm (7.25")
Strings in setup|ERNIE BALL 2223 / .009-.042 set
Modified parts|-
Repair/Maintenance parts|Cleaning, string change, rod adjustment, octave adjustment, string height adjustment, mortise and tenon adjustment, strap pin replacement
Other|-
Item Rank: B: Fairly scratched and used, but no problem for normal use.

Serial number: A046147
Country of manufacture: Japan
Case: Hard Case
Weight: 3.36kg
Truss Rod: No problem, rod is fine, checked up to 60 degrees to the left and right
Fretboard Height: No problem, fretboard is high enough.
String Height: Bass string side: 2.0mm above 12th fret
String height on treble string side: 1.5mm above 12th fret
Nut width: 42.75mm
Neck thickness near 1st fret: 21.48mm
Neck thickness near 12th fret: 24.52mm
SCALE: 648mm (25.5")
RADIUS: 184mm (7.25")
Strings in setup: ERNIE BALL 2223 / .009-.042 set
Repair and maintenance parts: Cleaning, string replacement, rod adjustment, octave adjustment, string height adjustment, rubbing, strap pin replacement

* The truss rod, remaining frets, and string height are measured by our staff at the time of setup, and may vary due to differences in climate, humidity, and other environmental factors.
The values are intended to be used as a reference at the time of purchase, and we do not guarantee that they will be the same when you receive the instrument.

* This item is a one-of-a-kind item and is listed on multiple malls at the same time, including in-store displays. We try to delete product information as soon as possible, but this is not always in real time.
We apologize in advance if the item is sold out after you place your order.

Specs

Product rank
B: Fairly scratched and used, but no problem in normal use.

12 months old

Serial No.
A046147

Country of manufacture
Japan

Case
Hard case

Weight
3.36kg

Truss Rod
No problem, rod is confirmed to be 60 degrees to the left and right.

Fret Remaining
No problem, there is enough fret height

String Height Low String Side
2.0mm above 12th fret

String height on treble string side
1.5mm above the 12th fret

Nut width
42.75mm

Neck thickness near 1st fret
21.48mm

Neck thickness near 12th fret
24.52mm

Scale
648mm (25.5")

RADIUS
184mm (7.25")

Strings for setup
ERNIE BALL 2223 / .009-.042 set

Repair and maintenance
Cleaning, string replacement, rod adjustment, octave adjustment, string height adjustment, rubbing, strap pin replacement