USED FENDER USA / 1977 Mustang [03]

We are pleased to announce the arrival of a 1977 Mustang.

The Student model was developed to promote Fender guitars at a price point affordable to students. It was a junior-sized model with a smaller body shape and shorter scale, and was developed together with the Duo-Sonic II in 1964.
Unlike the Duo-Sonic II, this model is equipped with a dynamic vibrato with a large range of effect.

This model was produced from 1974 to 1982 with an ash body.
The three-piece ash body weighs over 4 kg, but the sound is good and the playing condition is excellent.
The sound is characterized by its exquisite balance and firmness without the cheapness typical of mustangs, and it can be used in a wide range of genres.

The neck date is almost invisible, but the pickups are dated "102577".

Fret, nut, and pickguard (with "Made in Japan" sticker) have been replaced.
The arm is not genuine, and the groove that used to be for a strat has been forcibly shaved off.
* The bridge arm hole also appears to have been slightly shaved.

There are some scratches and dents, a few sticker marks on the elbow cut, and some small peeling of clear paint on the body back and body end.
There are scratches and rust on all hardware, and blue rust on the neck plate.
The neck is slightly twisted, but the frets have been fretted and are in good condition.

The neck is in good condition and has been fretted and nut replaced.

Vintage prices are rising every year, and it is hard to say when the prices of instruments of this age will also rise.
Please consider this as a good opportunity when the price is still smooth.
Truss Rod: Tightening direction: roomy / Loosening direction: slightly roomy
Neck Condition: Slightly twisted
Fret: about 70-80% remaining
Case: Genuine hard case
Attachment: Non-genuine arm
Serial Number:S715589
Weight: 4.155 kg

Item Rank: B: Fairly scratched & used, but no problem in normal use

Serial Number: S715589
Country of manufacture: USA
Case: Hard Case
Weight: 4.15 kg
Truss Rod: No problem, with a note that the rod has been checked up to 60 degrees to the left and right (not much left)
Fretboard Height: No problem, fretboard height is high enough.
String height on bass side: 2.0mm above 12th fret
String height on treble string side: 1.5mm above 12th fret
Nut width: 40.6mm
Neck thickness near 1st fret: 20.6mm
Neck thickness near 12th fret: 23.3mm
SCALE: 610mm (24")
RADIUS: 184mm (7.25")
Strings in setup: ERNIE BALL 2221 / .010-.046 set
Repair and maintenance: Cleaning, string replacement, rod adjustment, octave adjustment, string height adjustment, fret adjustment

* The truss rod, remaining frets, and string height are measured by our staff at the time of setup and may vary due to differences in climate, humidity, and other environmental factors.
The values are intended to be used as a reference at the time of purchase, and we do not guarantee that they will be the same when you receive the instrument.

* This item is a one-of-a-kind item and is listed on multiple malls at the same time, including in-store displays. We try to delete product information as soon as possible, but this is not always in real time.
We apologize in advance if the item is sold out after you place your order.

Specs

Product rank
B: Fairly scratched and used, but no problem in normal use.

12 months old

Serial No.
S715589

Country of manufacture
U.S.A.

Case
Hard Case

Weight
4.15kg

Truss Rod
No problem (not much left), as confirmed up to 60 degrees to the left and right of the rod with caution

Remaining frets
No problem, there is enough fret height

String Height Low String Side
2.0mm above the 12th fret

String height on treble string side
1.5mm above the 12th fret

Nut width
40.6mm

Neck thickness near 1st fret
20.6mm

Neck thickness near 12th fret
23.3mm

Scale
610mm (24")

RADIUS
184mm (7.25")

Strings for setup
ERNIE BALL 2221 / .010-.046 set

Repair and maintenance
Cleaning, string replacement, rod adjustment, octave adjustment, string height adjustment, fret adjustment