USED Ibanez / JEM90HAM / Steve Vai Model / Hoshino 90th Anniv Blue-green metallic texture [12]

A special Steve Vai model, produced in limited quantities to commemorate the 90th anniversary of Hoshino Gakki, is now in stock!
This model was produced only in 1998 as a commemorative model for the 90th anniversary of Hoshino Gakki, the brand holder of Ibanez. At that time, models by Joe Satriani, Paul Gilbert and John Petrucci were also available.

This Steve Vai model is based on the JEM7V with a metallic texture pattern and the same finish on the head top.

The pickguard is an aluminum mirror, a DiMarzio Evolution H-S-H is mounted, and the bridge is equipped with a Lo-Pro Edge Tremolo.

The maple neck with bubinga stripes is scarf-jointed and shaped like a super wizard, the fingerboard is ebony without tree of life inlays, the high frets are not scalloped, and the 24th fret has a 90th Anniversary Model The high frets are not scalloped, and a 90th Anniversary Model plate is embedded at the 24th fret.

This model is very rare to find used, so if you are looking for one, don't miss this opportunity!
There is a small paint chip near the tip of the head, and paint peeling around the elbow contour on the top of the body, the cutaway horn on the 1st string side, and the lower edge of the body top on the 1st string side.
There are also numerous small paint chips and flakes scattered on the body back, and there are stains on the rough surfaces of the paint that cannot be removed.
The mirror pickguard is generally dull, but this also cannot be removed by cleaning.
The guitar has been maintained and cleaned at our repair center, including strap pin replacement, and is in good playability condition.
The original hard case is included, but the exterior is cracked and one of the locks is broken, so the case is distorted when lifted by the handle.
Please note that the case is not suitable for transport, although it is fine for storage.
Item Rank: B: Fairly scratched and used, but no problems in normal use.

Serial number: F9806195
Year of manufacture: 1998
Country of manufacture: Japan
Case: Original hard case
Accessories: Certificate, Arm
Weight: 3.49kg
Truss Rod: No problem, rod is 60 degrees to the left and right.
Fretboard Height: No problem, fretboard height is high enough.
String height on bass side: 2.0mm above 12th fret
String height on treble string side: 1.5mm above 12th fret
Nut width: 43.0mm
Neck thickness near 1st fret: 18.0mm
Neck thickness near 12th fret: 21.0mm
SCALE: 648mm (25.5")
RADIUS: 1F:432mm (17") 12F:508mm (20")
Strings in setup: ERNIE BALL 2223 / .009-.042 set
Repair and maintenance parts: Cleaning, string replacement, rod adjustment, octave adjustment, string height adjustment, mortise and tenon adjustment, strap pin installation (correction of expansion screw holes), correction of end pin holes, installation of missing back panel screws

* The truss rod, fretboard rest, and string height shown above were measured by our staff at the time of setup, and may vary due to climate, humidity, and other environmental factors.
The values are intended to be used as a reference at the time of purchase, and we do not guarantee that they will be the same when you receive the instrument.

* This item is a one-of-a-kind item and is listed on multiple malls at the same time, including in-store displays. We try to delete product information as soon as possible, but this is not always in real time.
We apologize in advance if the item is sold out after you place your order.

Specs

Product rank B: Fairly scratched and used, but no problem in normal use.

Serial number F9806195

Year of manufacture 1998

Country of manufacture Japan

Case Genuine hard case

AccessoriesCertificate, Arm

Weight3.49kg

No truss rod problemNo problem, confirmed up to 60 degrees to the left and right of the rod

Fret remainderNo problem, sufficient fret height

String height: 2.0mm above the 12th fret on the bass string side

String height 1.5mm above the 12th fret on the treble string side

Nut width 43.0mm

Neck thickness near the 1st fret 18.0mm

Neck thickness near 12th fret 21.0mm

Scale 648mm (25.5")

RADIUS1F:432mm (17") 12F:508mm (20")

Strings at setup ERNIE BALL 2223 / .009-.042 set

Repair and maintenance partsCleaning, string replacement, rod adjustment, octave adjustment, string height adjustment, mortise and tenon adjustment, strap pin installation (correction of extension screw holes), correction of endpin separate hole drilling marks filling, installation of missing back panel screws