USED AMPEG / Little Stud Natural 1970s Active MOD Natural [11]

Long-term store display item at a special price!

70's made in Japan, little stud bass by Ampeg.

The body is made of laminated wood with sen (an alternative to ash) on the top and back.
Sen was often used on older Japanese models.
The neck is also made of stacked wood, and the fingerboard surface is maple.

The scale is 33.5" and the nut width is about 44mm.
The PU has been replaced and is currently equipped with a Duncan SMB-4D with ceramic magnet specification.
The preamp is a Korean brand G&B 2Band EQ.
In order to replace the PU and install the preamp, the cavity was extended with a counterbore and the pickguard was replaced.
The battery for the preamp is located under the pickguard.
There are some extra screw holes for pickguard mounting and some screw holes for PU mounting. The bridge has been replaced.

The body has scratches, dings, peeling paint, and paint cracks. The pickguard has minor picking scratches throughout.
There are paint cracks mainly on the top of the body. Large and small dents are scattered throughout.
The holes on both sides of the bridge are screw holes for bridge covers.
There are dings with paint peeling on the back of the neck on the 3rd and 8th floor, and small wood chips and scratches on the tip of the back of the head. The frets have been changed, and short frets that are not the correct length have been driven into the low and high positions a little too aggressively. There is also a chip on the fingerboard surface from the fret replacement. There is also a crack on the pickguard due to tightening.
There are also some cracks on the pickguard due to tightening.

* Due to the long-term display at a store, there may be scratches, stains, and other damages on the body, box, and accessories. Please note that there may be scratches, stains, and other damage to the unit, box, and accessories.
Product Rank: B+: Some scratches, but no problem in normal use.

Country of manufacture: Japan
Case: Non-genuine soft case
Weight: 4.43kg
Truss Rod: No problem (only a little left), with a note that the rod has been checked up to 60 degrees left and right.
Fretboard: Fretboard is defective and needs to be replaced when next time for repair.
String height on bass side: 2.5mm above 12th fret
String height on treble string side: 2.0mm above 12th fret
Nut width: 43.6mm
Neck thickness near 1st fret: 21.7mm
Neck thickness near 12th fret: 26.0mm
SCALE: 850mm (33.4")
RADIUS: 356mm (14")
Strings in setup: D'Addario EXL165 / .045-.105 set
Repair and maintenance parts: Cleaning, string replacement, rod adjustment, octave adjustment, string height adjustment, electrical repair, counterbore processing

* The truss rod, remaining frets, and string height are measured by our staff at the time of setup and may vary due to differences in climate, humidity, and other environmental factors.
The values are intended to be used as a reference at the time of purchase, and we do not guarantee that they will be the same when you receive the instrument.

* This item is a one-of-a-kind item and is listed on multiple malls at the same time, including in-store displays. We try to delete product information as soon as possible, but this is not always in real time.
We apologize in advance if the item is sold out after you place your order.

Specs of the item

Product rank B+: There are some scratches, but no problems in normal use

Country of manufacture Japan

CaseNon-genuine soft case

Weight4.43kg

Truss rod is not perfect, but we have checked the rod to 60 degrees to the left and right.

Fret remainder is defective and needs to be considered for replacement at next repair.

String height: 2.5mm above the 12th fret on the bass string side

String height: 2.0mm above the 12th fret on the treble string side

Nut width 43.6mm

Neck thickness near the 1st fret: 21.7mm

Neck thickness 26.0mm near 12th fret

Scale850mm (33.4")

RADIUS356mm (14")

Strings D'Addario EXL165 / .045-.105 set at setup

Repair and maintenance partsCleaning, string replacement, rod adjustment, octave adjustment, string height adjustment, electrical repair, counterbore processing