USED Fender Custom Shop / 1956 Stratocaster Neck Modify Sunburst [20]

This is a heavily modified 2001 1956 Stratocaster.
It has a bird's eye maple neck that has been reliced, a 7.5R radius, and a thicker V-shape neck.
Fender Custom Shop pickups are installed, but the wiring has been changed and the tone control has been changed from front + center to rear.
The joint plate has been replaced with a non-genuine one.
The joints have been modified to be bolted to the neck with an oni-me nut embedded in the neck side, instead of using wood screws.
The neck pocket has been dug down, and there is a gap in the wood (approx. 3.5 mm) due to a break in the paint inside the pocket.
The shim has been glued in place and angled to fit into the back of the neck pocket.
Because of the shims, the string height can be adjusted, but the string line is closer to the body, so there is not much room to adjust the PU height, and the screws may come off if the strings are lowered too far.
There are many modifications to the guitar, so it will be sold as-is with no warranty.

The neck is a little bit wavy and the low frets are slightly warped, but the amp sound is acceptable.
The neck has been reliced and the logo has faded, so we cannot tell if there are any new scratches or not, but there are no major dents on the neck.
The paint is cracked along the neck pocket edge, which was probably chipped during the digging process.
Paint has been removed from the back of the body, exposing some of the wood, and there are some marks where this has been corrected.
There is a large ding on the back of the body under the bridge plate with paint cracks and dents in the wood.
There are other scratches and dents that show signs of use.

After receiving the guitar, it has been cleaned, strings have been replaced, rods have been adjusted, octave has been adjusted, string height has been adjusted, rubbing has been done, and nut has been adjusted.

Item rank: B (average)

Year of manufacture: 2001
Truss rod : There is enough room.
Fretboard : 60～70
Accessories ： Hard case / Genuine tremolo arm
Country of Origin ： USA
Weight ： 3.44kg
Serial ： No serial number

Truss Rod : No problem (slight waviness)
Fret height is sufficient.
String height (bass string side)|2.0mm above 12th fret
String height(treble string side)|1.5mm above 12th fret
Nut width|42.2mm
Neck thickness(near 1st fret)|22.2mm
Neck thickness (near 12th fret)|23.6mm
SCALE|648mm (25.5")
RADIUS|184mm (7.25")
Strings in setup|ERNIE BALL 2223 / .009-.042 set
Repair and maintenance parts|cleaning, string change, rod adjustment, octave adjustment, string height adjustment, rubbing, nut adjustment

* The truss rod, remaining frets, string height, etc. are the setting values at the time of setup and adjustment at our repair center.
* This item is only available as a one-of-a-kind item.
We will try to delete the product information as soon as possible, but it is not always in real time.

Specs

Truss rod is fine (with a slight waviness).

Fret height is high enough.

String height (bass string side): 2.0mm above the 12th fret

String height (treble string side) 1.5mm above the 12th fret

Nut width 42.2mm

Neck thickness(near 1st fret)22.2mm

Neck thickness (near 12th fret)23.6mm

Scale648mm (25.5")

RADIUS184mm (7.25")

Strings at setup ERNIE BALL 2223 / .009-.042 set

Repair and maintenance parts cleaning, string replacement, rod adjustment, octave adjustment, string height adjustment, mortise and tenon nut adjustment